Capstone week 8 Fady Riad

 This week's goal was to get the pressure sensor ready to be tested with the rest of the lab. The setup seemed right after I have done enough research but the pressure sensor was not working still. I switched out the sensor to a new one and after a few tries it is finally working and the setup is ready to be used on our main lab setup.




Dr. Gordon approved my ethics topic and I started to do some research on the topic. There seems to be little information surrounding this issue. But this is what I have found so far, FDA ordered a class I recall of 700 devices after 22 complaints and 3 deaths in 2019.



I also researched the use of laser volume-measuring devices. I came across the LLT100 laser transmitter which could accurately measure level, distance, and position over short and long rangers. We are looking for a device to measure and monitor the change in eye ball volume change over time. If the the volume does not change that means the inflow=outflow, if it increases means inflow > outflow, and if it decreases then outlfow > inflow. I am not sure if this device would work for our purpose but I am still looking into it.






Comments

Post a Comment

Popular posts from this blog

Week 11 Alex

 this week mainly consisted of preparing for the final presentation and final notebook  Some research on different silicone housing can be done  -  Plastic Injection Molding | Custom Low-Volume Plastic Parts (protolabs.com) -  Molded Rubber Parts - Aero Rubber - Molded Rubber Products -amazon (cheap)  Amazon.com : silicone mold making -  ProMed Molded Medical Silicone Component Manufacturing Company (promedmolding.com) (biocompatible) - Silicone Biocompatibility for Medical Components - Miwo (miwosilicone.com) (biocomptable) -DIY silicone molding??  Make Your Own Silicone Molds - Easy Mold Making (Mould) - For Candle Or Resin Molds - Bing video
Read more

Week 7 - Brinkley

Image
 This week was shakedowns, bench top testing, and more shakedown designs. Our materials all hadn't come for some of our shakedowns, so we focused on our bench top testing to begin, then we designed more shakedowns.  BenchTop Testing Our bench top testing is done on the Ahmed valve to see how it preforms when we can control the flow, resistance, and pressure. We had to create an encasing for the Ahmed to simulate fibrosis and add it to our bench test. Here are a few pictures of Kierstin and I working on the setup, and get the flow sensor to work in our system. Fady is working on the pressure sensors, so we will be able to execute this bench top testing on Wednesday during class time. This set up took so long because we had to find supplies in Dr. Rickard's lab that we could experiment with and see if they would fit in our set up.  ShakeDown #1 The first shakedown we were able to do with the supplies we had was seeing how water flowed through a tube when it was partially bl...
Read more

Week 9 - Brinkley

Image
 This week was a lot of testing and research. I am still working on the dissolving component and figure out that data, which will make more sense with time hopefully. When we were in the capstone block, we did a couple of shakedowns, we did a brief resistor in parallel test that worked great, Fady set up the sensors, and we modified parts we already had to make them work for shakedowns.  The research I did this week was about materials. I researched silicone sheets, silicone molding, glue, and sutures. For each category I found biocompatible and regular options. The regular options are much cheaper and easier to get.  Here are the links to the products I found:  Research Mold and Curing Silicone:  Biocompatible: https://www.elkem.com/silicones/offer/healthcare/medical-grade/liquid-silicone-rubber/ I would suggest soft or mid durometer because it would be less preventative of the tube expanding. Less resistance. Another option is:  https://products-silicones...
Read more